Should I upgrade from a EA6900 to a R8000?
Hello, I have been using FreshTomato on the EA6900 for quite some time and it is working really nice and stable (thanks devs). I have a 600 mbits connection and it appears that the EA6900 can not reach...
View Articleiptables module recent: how to get the --mask parameter working
i am trying to get --mask working in the module xt_recent. the manual states: --mask netmask but does not state howto. i tried 255.255.255.248, 29 and /29, non of these worked, error: iptables v1.6.2:...
View ArticleCan you format the routers internal storage to how it was factory?
Using a Linksys EA6900 router with different firmware such as Asus Merlin 374 fork and FreshTomato After clearing NVRAM thoroughly and doing a firmware upgrade i notice the system log still has old...
View ArticleIgnore unknown devices in VLAN1
Hi! I have 2x VLAN: internal + guest. How can I ignore the DHCP requests only in "internal" VLAN? Or do you have any script, what can send a warning in e-mail, in case of any unknown device is...
View ArticleWNDR3400v1 and E3000, Do They Share Components?
This might completely off base but I thought I would try to see it there may be a fix in here somewhere. As I mentioned before, starting with FT2020.2, whenever I make a change to almost any of the...
View ArticleBelkin F9K1102: Tomato bring-up
The original first message of this thread, when tomato was not yet ported, can be found at the bottom of this post. Tomato is now operational on the F9K1102 (v1 and v3 only), so I've changed the first...
View ArticleIptable changes (if needed) for netgear r7000 with fresh tomato from the...
Basically a novice here but would appreciate help from experts who can tell me what they did on their routers for added security. If it is good enough for you as the experts, then it should be good...
View ArticleR7000 Netgear - recent purchase, firmware flash blocked by Official firmware
Hi everyone! I think I finally found everyone! I hope I’m not breaking any forum rules - if so, let me know! Had an old Netgear nighthawk R7000 bite the dust after a lightning strike (banged my head...
View ArticleConfused how VLANs and firewall rules are connected
My first contact with the concept of VLAN was when I read about separating my Wi-Fi guests from my main network (protecting the main network services from being accessed by guests). The gist of setting...
View Articleiperf - where is it in freshtomato ui?
As per the subject - i've clicked through every menu item sequentially but I can't spot it... Thanks!
View ArticleTenda AC15 (AC1900) - Tomato firmware support
Interesting ac1900 router released recently by Tenda and is on sale for $80. It uses the same bcm4708A0 and bcm4360 chips as Asus RT-AC68U, and the appearance is very similar too. Wonder if anyone had...
View ArticleTenda ac15 transmission
Hello, can you tell me how to install transmission, it is not in the firmware, is an NTFS disk connected to Tenda AC15?
View ArticleLinksys-EA6200/EA6350v1 Freshtomato-ARM & Discussion
Two Linksys Single Core Models the "EA6350v1/EA6200" have been released. Flashing the Linksys models will require the xvortex cfe modification in order for stability on these two models. Note: If you...
View ArticleIPTV on seperate interface, how can I convert that to LAN?
Hi folks, Here is my setup: ISP router in bridge mode FreshTomato LAN 1<--------------------------------------------->WAN (PPPoE) LAN 4<-----------(contain IGMP IPTV)------------>LAN4 For...
View ArticleFeature Request - Port Forwarding Interface Menu
Good morning, Without any real knowledge of how port forwarding currently works behind the scenes, I'm speaking in large generalities so please forgive the ignorance. I assume when I port forward in...
View Article[Fork] FreshTomato-MIPS - development discussion only - for support always...
[Fork] FreshTomato-MIPS - development thread ==================================== [FreshTomato-MIPS] Forked off from Tomato-MIPS by Shibby. Project page: https://freshtomato.org Latest version: 2020.5...
View ArticleFreshTomato - R7000 - NAS and USB options not available, USB not working
Hi Guys, I'm new to this forum and to the world of custom firmware. First, let me start by saying that you are doing good work, Thank you. I set up my R7000 with the FreshTomato Firmware 2020.2 K26ARM...
View ArticleRT-AC56R 5GHz with Defaults 80MHz Channel and Country/Region United States is...
A default (NVRAM reset) now provides a "United States" Country/Region default for 2.4GHz and 5GHz radios with 2020.5. However, the 5GHz radio default is shown at 80MHz in the Basic settings, whereas...
View ArticleFreshTomato
I am trying to send email notifications for WAN UP. I created script in Administrator> Scripts > MultiWAN But it's not working. Any hep? Using 2020.3 version for MIPS
View ArticleClik here to view.
DHCP Forwarder Option in Freshtomato?
Hi Everyone, I was going through a Cloudflare thread explaining Gateway deployment using Rasberry Pi, Pi-Hole and DoH. There was a step where the author set "DHCP Type" to "DHCP Forwarder". Is there a...
View Article