Prevent guest wifi clients from using their own/static DNS?
Hello, I am running Tomato by kille72 2017.3 on Netgear R7000. In addition to my regular wifi, I set up a separate VLAN (br1) for guest wifi. This guest network uses a different DNS in order to filter...
View ArticleFTP Failed to retrieve directory listing
I've googled this since I've seen others with similar problem, but none of the solutions I've found fixed my problem, so asking here... My router sits behind an AT&T gateway (modem/router), so I...
View Articlebug: cru
i found a bug in the cru script. if while adding a command, {enter} is pressed, {enter} will be written into the cron file. the unique ID will end up on a separate line. when this happens, the cron job...
View ArticleChanging the VLAN ID on br0
I am using my Netgear Nighthawk R7000 to provide wifi connection to my pfSense router. I also wanted to provide multiple SSID as well. When I tried to the change the VLAN ID of br0 to VLAN 05, with it...
View ArticleOpenVPN CPU cap
This must be one of the most common topic on this forum. Basically I'm using a VPN provider (windscribe.com) and despite my 100Mb connection the maximum I can't get over VPN is about 10Mb when...
View ArticleTenda AC18 (AC1900) - Tomato firmware support
The Tenda AC18 (AC18) router released in 2016. It is powered by Broadcom BCM4709C0 @ 1.4 GHz chipset, 256 MB RAM and 128 MB flash. The AC1900 router is compatible with IEEE 802.11a/b/g/n/ac standards,...
View ArticleClik here to view.
Can VLAN GUI port order be corrected?
Is it possible to alter the VLAN GUI so the port order shows correctly? I have a fresh firmware install and my NVRAM has been cleared (thorough). Here are the physical port states. This is correct....
View ArticleIEEE Power Save Polling
Hey guys, My Belkin F7D3301 router with Shibby Tomato 140 is disconnecting both my Sensi Thermostat and my Hp Printer occasionally. These devices are 2.4 GHz only and apparrently use IEEE Power Save...
View Articlebug: dns
Hi to all. Shibby thank you for firmware. I have a some bug in Linksys e3000 build 140: My ISP use L2TP without DHCP. I forced to set manual IP address, netmask, GW, login/password/VPN server and DNS...
View ArticleCompiling advancedtomato-arm v140
Hi! I am trying to compile advancedtomato-arm v140 on ubuntu 16.04 x64. Starting with a clean install, here are my commands: $ sudo apt-get update $ sudo apt-get install build-essential autoconf m4...
View ArticleVLAN woes!
I have been using a TL-Link WA901ND Access Point providing access through my pfSense router. I used the TL-Link device to provide 4 SSID where each SSID was attached to my VLAN on the pfSense router....
View Article"the wireless router is not in rescue mode" ?? asus rt-n66u help
hey guys I just got a asus rt-n66u and tried to install tomato to it for the first time, after holding down the reset button and plugin the power cable for RT-N66U and go into firmware restoration...
View ArticleNothing compares to Tomato
I finally decided to try for a new firmware since Tomato seems to be at a dead end, and I have been playing with LEDE and Gargoyle, and I still want to keep Tomato but I am concerned about it's...
View ArticleUsing Scheduler to turn on/off specific Access Restriction rule
I am trying to use the scheduler in Administration to turn on/off one of the Access Restriction rules thru a command. Is this possible? Where can I find a list of commands that are valid to enter?...
View ArticleAdvancedtomato setup help
Hi one and all First post and hopefully a good starting point in open source firmware and learning. I’m just looking for a working guide so I can get this working properly. Set up Vigin Media Superhub...
View ArticleRemove stale devices from wl0.x device lists
I'm using tomato shibby (MIPSR2-140 K26 USB AIO) on a RT-N16 and I've set up virtual wireless interfaces on additional bridges. All works as it should, however, I notice that certain clients appear...
View ArticleDisable dnsmasq
I'm just curious what's the appropriate way to disable dnsmasq on shibby? I don't see a gui option for it. kill `pidof dnsmasq` Doesn't seem to do it. "Use internal DNS" is unchecked but I still see...
View ArticleUsing ipset to bypass a VPN
I'm attempting to use ipset to divert certain URLs around my VPN connection (the "Netflix" problem) with Tomato (Shibby 1.28) on an Asus RT-N66U router. The set of IP addresses I end up collecting...
View ArticleClik here to view.
Settings up VLANs with differing DNS servers, dnsmasq, and VPN client.
I am trying to set up 3 mostly different local networks, and I am only ever to *almost* get what I am looking for. I have to break something somewhere to make something else work. I've been through all...
View ArticleBelkin F9K1102: Tomato bring-up
The original first message of this thread, when tomato was not yet ported, can be found at the bottom of this post. Tomato is now operational on the F9K1102 (v1 and v3 only), so I've changed the first...
View Article